So, this week has been a good one. The doc told me I needed to take some time away from work, so I've spent it mostly focused on working up Proj H and V.
I got most of the base colors and build done for H. I just need a couple details to show up in the mail so I can finish the cockpit build, and do the final assembly. As it is now, it's time to start all the fiddlybits of doing the shading, rusting and dusting.
The chipping has been completed, and I've done a lot of the panel shading completed. Now I'm working on slowly building up all the score marks, oil streaks, leaks, and and impact damage.
Oh, and every good mechwarrior names their ride, yeah?
Considering that Jrjrjr is a 40K demons player.... it fits his style. The closeup looks like crap because I haven't finished all the blending, but ..yeah.
Friday, November 13, 2015
Tuesday, November 10, 2015
slow but steady
Work on Project H and Project V continues.
I have been working concurrently with both Project V and H,
for the most part working from the ground up.
For project H, the switch will be in the greeblies on the
back.
Since all the custom work for both of these is in the torso,
I've been working on the assemblies from the hip down. Granted, Proj. H
is *all* custom, but you get the idea.
For V.. I splayed the hips a little, which has the effect of
also slightly tilting the torso plane. When I put the torso on, that
twist should add to the dynamic pose and give it a good action feel. The
paint scheme for V is a mostly-black with red highlights scheme for HWSNBN's
merc unit. I hate black. Black is such a challenging color to
weather nicely. I'm building it with a battered-and-used look that feels
appropriate for a Merc unit that lives off salvage and luck. The black
paint is put over a previous-owner's gray colorscheme, and that is showing
through the chips and scratches and scrapes with some going all the way down to
the core armor. The fun part of black is that the usual weathering
techniques of oil leaks, carbon scoring, smudging and shading doesn't show
against the dark color. So I'll have to use dirt and off-shading to try
to give it a heavily beaten look.
Below is the way I have it looking so far. Before I hit it
with the next wave of shading, I'll give it a pass with matte varnish, to dull
down the shiney, and hopefully that'll help with the aging techniques.
The torso work for the V is coming along. I've managed to hollow it out and get the battery compartment ready. The batteries will go under the right arm with the switch hidden as mentioned above. I still need to get the head ready, but the cockpit will be built into a tub fastened to the head canopy.
As for Project H, his chosen scheme is a base of Red, with
Gold and Black accents. I'm also going with the Mercenary
Mech beaten and weather-worn look for the Mech, and will work in some heavier
damage to the hatchet and lower legs. The red can take the shading better
and I can use different tones for various panels, etc., while the damage on the
legs makes sense; the Hatchet man’s notoriously lightly armored legs are well
known as primary targets during combat, and any mech that is built for closing
to melee range is going to bear the scars of kicks being delivered in desperate
retribution.
This is the base color tone.. there is still a huge amount
of detailing for the panels and joints to do. This is also my first
attempt at using pigments and I'm very not happy with it. I'll be
practicing a bit more on some other equipment and then touching up on it.
I have a feeling that I'll be needing pigments for the Victor build as well.
For the most part, the parts for H go together well. I
pinned the ankles and got a decently dynamic pose going, incorporated with the
upper body holding the hatchet raised high and the left hand pointing for a shot
from the ML. The one thing I don't like about this mech is the lack of
pose ability to the cockpit. Then again, most Mech’s don't have a
variable cockpit and that's one of the nice things about the Victor. It
really is amazing what just that little turn of the head can do to communicate
intent and action. That, however, is all part of the mech design..
not unlike the Hunchback or the Warhammer. The cockpit is locked and
there really isn't a way to design a "pose" into it otherwise.
However, it is hollowed and ready, with the overhead light fixed in place.
The more I do this one, I'm finding little things that would
help for future designs. It seems that when doing the Victor, Mr. Fusco
used some very thin panel overlays rather than scribing in panel lines.
Well that's gorram intelligent. Simple, more blocky parts make for easier
building and designs, but sadly, that is exactly why Mr. F passed on this one..
: ) "all those damned curves!" hehe.
Sunday, October 4, 2015
Productivity.
Well, productive weekend. I had a TON of stuff to do for work, but since it was a whole lot of "do this, then wait to do that, rinse, repeat".. had a lot of time to fiddle with my hands.
So, I took some supersculpey firm, and tried again to carve a major part out of clay. It didn't work so well when I did the foot for the DDC, and this time I had challenges as well. The hip is a weird ellipse shape as well as being on a sharp angle up toward the pivot point of the torso. But, it actually came out better than I thought it would. I plated it up with some 1mm sintra pieces to give it texture and carved in some panel lines. There are still some inconsistencies in the layers but the panels and lines seem to break it up enough to the point that it works.
While I was at it, I got the shoulder piece, upper arm and lower arm done. The arm parts are reversable to swap from right to left, so that helps. I poured molds for all of the above and pulled casts for them all and I'm fairly happy with the result.
These aren't quite up to the ol' pros standards (Fusco, Messydesk, et al), but they work. The casts give me a good base to work from, and with cleanup, extra panels and greeblies, they should be acceptable.
I got the arm articulation pinned up just to check and they worked just about where I'd like. I kinda might want a change to the shoulder joint for more up/down transition, but I can still pose JrJrJr's in a pretty dynamic option. The available poses for the articulation across the board is pretty good.
Yet to do, I have the hands, torso and head. I'm not excited about carving up the hands. Since the right is a fist, that'll be easy. I might cheat and just mount the ML for the left arm on the wrist.. but I think that's cheating. : ) As for the head, I would like to see a head that can turn a bit, but that's a bit tough given the position it has in the torso. I think that the turn of a head really can add dynamicism to the pose, but it may not quite work with this mech. We'll see.
Anyway.. that's it so far. More to come.
So, I took some supersculpey firm, and tried again to carve a major part out of clay. It didn't work so well when I did the foot for the DDC, and this time I had challenges as well. The hip is a weird ellipse shape as well as being on a sharp angle up toward the pivot point of the torso. But, it actually came out better than I thought it would. I plated it up with some 1mm sintra pieces to give it texture and carved in some panel lines. There are still some inconsistencies in the layers but the panels and lines seem to break it up enough to the point that it works.
While I was at it, I got the shoulder piece, upper arm and lower arm done. The arm parts are reversable to swap from right to left, so that helps. I poured molds for all of the above and pulled casts for them all and I'm fairly happy with the result.
These aren't quite up to the ol' pros standards (Fusco, Messydesk, et al), but they work. The casts give me a good base to work from, and with cleanup, extra panels and greeblies, they should be acceptable.
I got the arm articulation pinned up just to check and they worked just about where I'd like. I kinda might want a change to the shoulder joint for more up/down transition, but I can still pose JrJrJr's in a pretty dynamic option. The available poses for the articulation across the board is pretty good.
Yet to do, I have the hands, torso and head. I'm not excited about carving up the hands. Since the right is a fist, that'll be easy. I might cheat and just mount the ML for the left arm on the wrist.. but I think that's cheating. : ) As for the head, I would like to see a head that can turn a bit, but that's a bit tough given the position it has in the torso. I think that the turn of a head really can add dynamicism to the pose, but it may not quite work with this mech. We'll see.
Anyway.. that's it so far. More to come.
Thursday, October 1, 2015
more work
Well, I did some cleanup and rework on Proj. H's legs. I found that I don't like the ankle. I am wondering if it would be better as a ball-and-pin.. where the ball sits into the ankle of the armored shin, and a pin goes into the top of the foot. What I have done for this one is just cut the ankle and pinned it for rotation parallel to the ground. If I were to try casting it for others, that might be what I'd think about, but I'm not sure if I'm willing to go that route yet.
Even though I beefed up the legs a little, they still have that spindly look that the H is notorious for, so that was a side benefit. I also re-cast the greeblies for the outside of the hip joint and I'm much happier about that one.
Even though I beefed up the legs a little, they still have that spindly look that the H is notorious for, so that was a side benefit. I also re-cast the greeblies for the outside of the hip joint and I'm much happier about that one.
I was starting to get a bit concerned that it might be a bit out of scale to the 45 ton size of the Hatchetman. So I pulled the lower part of Project V-1 and set it side-by-side with them, and it looks like it just might be right.
Now on to the hip and torso.....
Wednesday, September 30, 2015
oops
..crap. I was just going through some of the sketches for the inspiration for Project H, and realized; I forgot the jumpjets.
Ok.. I can fix this. They're mounted to the legs, so I can make Jumpjet greeblies to add to the thigh or shins.
Another thing I'm still chewing on is the AC-10 mounted in the right torso. In almost all the sketches, it's represented as just a hole in the front armor. Blech. I think that looks stupid. But then, just having a tube sticking out of the armor would look just as bad. I might want to alter it a bit to mount a gun assembly something like the under-slung package that the Atlas carries. At least that would have a more interesting look to the build.
The MLs mounted to each arm are simple enough, but that AC-10 definitely needs some design work.
Ok.. I can fix this. They're mounted to the legs, so I can make Jumpjet greeblies to add to the thigh or shins.
Another thing I'm still chewing on is the AC-10 mounted in the right torso. In almost all the sketches, it's represented as just a hole in the front armor. Blech. I think that looks stupid. But then, just having a tube sticking out of the armor would look just as bad. I might want to alter it a bit to mount a gun assembly something like the under-slung package that the Atlas carries. At least that would have a more interesting look to the build.
The MLs mounted to each arm are simple enough, but that AC-10 definitely needs some design work.
Tuesday, September 29, 2015
coupla pix -Project H.
First attempt at the legs.
Given my experience casting.. I'm not entirely unhappy.
The foot came out ok.. a bit of cleanup and it should be ok. The lower shin..same. I'm not very happy with the scribe lines but I think I can clean that up too. The upper thigh is better, that one I'm actually happy about. The hip joint is ... meh. I cast a greeblie for the the outside of it and that I am NOT happy over. However, I have the greeblie from which I cast it that I can use. .. I'll try a second run on that.
The foot came out ok.. a bit of cleanup and it should be ok. The lower shin..same. I'm not very happy with the scribe lines but I think I can clean that up too. The upper thigh is better, that one I'm actually happy about. The hip joint is ... meh. I cast a greeblie for the the outside of it and that I am NOT happy over. However, I have the greeblie from which I cast it that I can use. .. I'll try a second run on that.
the molds
The first set of casts
First set of casts with the original pieces. The thigh piece lost the center detail strip in the de-molding, but it shows clearly on the cast pieces.
Monday, September 28, 2015
It begins.
So, Project H and Project V-1 are underway. I do not
expect P-H to be up to the standards of followers of guys like Fusco or
MessyDesk, but hopefully it'll be good enough for the son of
he-who-shall-not-be-named. The intent is to make the pieces such that I
can pseudo-cast them. In essence, I'd like to be able to replicate them a
couple of times, but the expectations I have on the casting are not high.
I don't own a de-gasser or a pressure caster, both items I would like to
acquire at some point. However, I did pick up some Mold-star 20-t and a
some big ol' jugs of smooth-cast 300. At the least, the parts should come
out serviceable and give a decent base shape upon which to build up the details
and final structures for it.
So, to start off project H... the foot.
The 'Mech's design, as shows in the TRO, looks crappy.
It's just waaaay to spindly to be functional to my engineering brain. So
the build I'm making is going to have a much more MWO feel to it, and while
it'll still have the curves and main shapes that the H is famous for, the legs
and arms are going to be a bit beefier and more armored. I have a concept
in mind for the hip joint that'll allow for it to open its stance, and that
should allow for some dynamic poses. As I write this, it comes to me that
also changes the way I'm going to do the hip-torso parts, making it as a 3-part
linkage rather than a ball/socket or Pin.
(I love it when my engineer brain can play)
This is my first use of the Moldstar 20-t. it's
basically the same as 16-T as far as setup time and cure time. The big
difference I see is the color. 16-t A & B are blue and white, giving
an off-blue color when mixed and you can see the unmixed "a"
part. This stuff is all translucent, so it's harder for me to tell
if it's fully mixed. The benefit is that I can see the airbubbles that
are in the matrix as it's mixed. (hence the desire for a
de-gasser.) I don't think that there are MORE bubbles in this than in the
16-T, just that I can actually see them, so now I'm aware of them.
However, I have been happy with the 2 test molds I've made with this stuff so
far.
The first castings of the Proj H feet came out and they're
up to the standard I expected. They're decent if a bit rough, but the
general shape now is good compared to having to build them each up from
stock.
Project V-1 has my hands shaking. I commissioned Mr
Fusco for the V and that was no small request. The kit is absolutely
superb and I love this machine. The catch is..now it's time to cut into
it. Yep, building up the cockpit and lighting the thing, which means
taking the dremel to the head and torso. That's the part that I am just
a-skeered to do. Yeah, it'll be fine once the blade hits resin, but it's that
first dig that's hard. I have blue 1.8mm leds to hook up for the
lighting and I'll put that in the forward upper part of the cockpit head and
since it'll be a closed cockpit, I only really have to detail the pilot, seat
and the back of the compartment. I'm thinking of giving it a bit of a
Millennium falcon look, with glowy switches in the back, but then I think
that's a bit out of character for the machine. It really should have more
of a fighter/bomber look, with the controls easily accessable for a single
pilot. So I have to find a good mix of "looking cool" and
"looking functional."
Oh yeah.. Neurohelmet. This one has to have the
old-school Inner-sphere neuro helmet. It IS an old-school Inner Sphere
Merc 'Mech, after all.
I want to build this up with as much a realistic look as
possible. I have to determine the battle damage level, paint scarring,
and the general stance. The ankles and knees for this will need to be set.
The hip and shoulders are likely more posable, and can be left movable. I
am considering pinning the elbows so they can be posable as well, but that may
be more effort than it's worth. It may just make sense to set the whole
machine in a threatening pose with the AC-20 raised.
Also, the SRM-4 launcher on the front torso is another point
for detail. I'd like to drill them out a bit more and drop in
"missile tips" so it has the loaded launcher look. I haven't
figured out what to use to make those tips yet, but I'll come up with something.
This one will definitely be battle damaged. I'm contemplating having a couple parts have the "salvaged from the battlefield" look with either a different paintjob or alternatively a "very very brand new" paint scheme to it, complete with missmatched colors and so on. ..
Here goes......
Here goes......
Subscribe to:
Posts (Atom)







































